V-Kote Tek™
The Ultimate Deck Waterproofing System.
Extend The Lifespan of Your Dec-K-Ing Surface
Any waterproofing system is only as good as its weakest point. Our V-KOTE TEK™ Waterproofing System is the most technologically advanced deck waterproofing system on the market. It is engineered to add protection to the most critical areas of your project, offering PVC coated accessories and pre-manufactured solutions to give your sundeck, rooftop patio, residential or industrial roof impermeable protection against the elements.
V-KOTE TEK™ details are manufactured in a controlled environment allowing for easier and faster installation on site. With 40 years in the deck waterproofing industry, we know from experience where water is most likely to infiltrate your home or building.
V-KOTE TEK™ Waterproofing Deck Components
V-Kote details available in the same colour/pattern as your DEC-K-ING membrane
The V-Kote Tek door flashing is a one piece solution for addressing the critical areas of water migration around the exterior door. Designed to cover the entire corner of the door threshold of a standard 4" opening. Available as shown or sold as a 2 piece package for the right and left sides of the door.
The one piece molded PVC scupper allows for DEC-K-ING vinyl to fuse directly to the scupper. A PVC downsoup adapter is also available.
One piece spun aluminum drain outlet that has been PVC coated. Simplicity of design, the drains PVC coating provide a permanent 100% seal when heat welded to the PVC membrane. Four fastening rings allow for a tight fitting grate into the drain.
This one piece solution covers all four sides of a penetrating post eliminating hard to do on site work for a waterproof finish. The opening allows the flashing to easily wrap and fit snug around the post with the overlap heat welded to the PVC membrane. Available in both standard and custom sizes.
A downspout is terminated in a similar way to a post or pillar. A PVC membrane manufactured boot is glued with DEC-K-ING Contact Adhesive around the unit and heat welded to the deck.
The one piece -V-Kote Tek solution covers the critical junction where the deck meets the wall. This factory made flashing joins the vinyl on the deck, the edge flashing and the wall together in one watertight solution.
Two part V-Kote Tek waterproofing solution for deck railing posts. The factory made PVC cover fits over a high density poly ethylene block. This will elevate the rail base off of the deck surface, eliminating water migrating under the baseplate and through the fasteners. Water will flow around the block and continue to the edge of the deck.
The V-Kote outside corner flashing is a safe solution to ensure a watertight corner. The factory made flashing eliminates the need for poorly handmade on-site details and creates a clean finish. Available in the same colour/pattern as your DEC-K-ING membrane.
DEC-K-ING deck edge flashing is made of galvanized metal and laminated to a PVC sheet. The vinyl coated flashing allows for a watertight termination of the vinyl to the edge of the deck by hot air fusion. Water flows off the deck and the 1/2" kick drip on the bottom helps deflect water away from the house. Available in four colours to match or complement your home's exterior.
The V-Kote inside corner flashing is a safe solution to ensure a watertight corner. The factory made flashing eliminates the need for poorly handmade on-site details and creates a clean finish. Available in the same colour/pattern as your DEC-K-ING membrane.
V-Kote Tek custom parts are available for countless waterproofing challenges. No matter your challenge, chances are good that GLOBAL DEC-K-ING SYSTEMS has already encountered your issue and can fabricate a solution in a timely manner.
The DEC-K-ING fastening bar is an aluminum termination bar with a butyl tape along the inside track. The fastening bar can be installed over the vinyl in areas where additional protection is needed. This includes under a sliding door, along the edge of a wall or where the deck edge flashing isn’t being used. Available in Grey or Beige.
One piece PVC coated aluminum overflow with a two inch opening for easy fitting to a standard mechanical clamp. Deck membrane is easily fused to the PVC coated overflow for a reliable waterproof finish.
Corners
PVC Coated Metal Flashing
Scuppers & Overflows
Drains
Post Wrap
Deck Wall Transition
Door Flashing
Downspout Boot
Railing Base Block & Cover
Have A Question?
To learn more about our V-KOTE TEK™ Waterproofing System, and how it can be used to extend the life of your outdoor project, please contact us.
Find A Dealer
We have a worldwide network of certified dealers and installers. If there isn’t one near you contact us and we can ship our products to you – wherever you are located.